Thermal Physics Formula Sheet: Heat Capacity, Gas Laws, and Thermal Efficiency Explained
thermal-physicsheat-capacitygas-lawslatent-heatinternal-energythermal-efficiency

Thermal Physics Formula Sheet: Heat Capacity, Gas Laws, and Thermal Efficiency Explained

SStudyPhysics Editorial Team
2026-11-21
7 min read

A practical thermal physics formula sheet covering heat capacity, latent heat, gas laws, work, internal energy, and efficiency.

This thermal physics formula sheet helps you choose the right equation for heat capacity, latent heat, gas laws, work, internal energy, and thermal efficiency. Use it as a reusable checklist: identify the physical process first, list known and unknown quantities, convert units, apply a consistent sign convention, and then test whether your answer is reasonable.

Overview

Thermal physics questions often become difficult because several related quantities appear together. Temperature measures how hot or cold a system is, while heat is energy transferred because of a temperature difference. Internal energy is the total microscopic energy stored in a system. These ideas are connected, but they are not interchangeable.

Before selecting an equation, ask what is changing. Is a substance changing temperature, changing state, expanding, being compressed, or operating as part of a heat engine? The answer usually identifies the correct formula more reliably than searching for a familiar symbol.

SituationEquationSymbols and units
Temperature changeQ = mcΔTQ: energy transferred (J); m: mass (kg); c: specific heat capacity (J kg−1 K−1); ΔT: temperature change (K or °C)
Change of stateQ = mLL: specific latent heat (J kg−1); temperature remains constant during the idealized phase change
Ideal gas relationshippV = nRTp: pressure (Pa); V: volume (m3); n: amount (mol); R: 8.31 J mol−1 K−1; T: kelvin (K)
Fixed amount of gaspV/T = constantUse when n is constant; compare two states with p1V1/T1 = p2V2/T2
Work done by a gas at constant pressureW = pΔVW: work done (J); p: pressure (Pa); ΔV: change in volume (m3)
First law of thermodynamicsΔU = Q − WHere W is work done by the system; ΔU is the change in internal energy
Thermal efficiencyη = useful output energy / input energyMultiply by 100 for a percentage

Some courses define work as work done on the system rather than work done by the system. In that convention, the first law may be written as ΔU = Q + Won. Always follow the convention stated in the question or your course materials, and write it beside your working before substituting values.

Checklist by scenario

1. A substance changes temperature

Use Q = mcΔT when the material remains in the same state and its temperature changes. Find the mass, the relevant specific heat capacity, and the final-minus-initial temperature. For example, heating 0.50 kg of water from 20°C to 80°C requires the temperature difference ΔT = 60°C. A temperature interval of 60°C is also 60 K, so either unit is suitable for ΔT.

  1. Check that the mass is in kilograms.
  2. Use the specific heat capacity of the actual material.
  3. Calculate ΔT = Tfinal − Tinitial.
  4. State whether the energy is absorbed or released.

If the material warms in stages or contains more than one substance, calculate each energy change separately and add them. A container, heater, or surrounding material may need its own term if the question includes it.

2. A substance changes state

Use Q = mL for melting, freezing, boiling, condensing, or sublimation. The relevant latent heat is either the specific latent heat of fusion or the specific latent heat of vaporization. During the idealized phase change, the temperature stays constant even though energy continues to be transferred.

Do not use Q = mcΔT for the phase-change section of a heating curve. If a problem includes both warming and melting, split it into stages: use mcΔT before the change of state, mL during the change of state, and mcΔT again after the material has changed state.

3. Pressure, volume, and temperature of a gas change

Use the ideal gas law, pV = nRT, when the amount of gas is known or can be calculated. Pressure must be in pascals, volume in cubic metres, and absolute temperature in kelvin. Convert Celsius with T(K) = T(°C) + 273.15; do not insert a Celsius temperature directly into a gas-law equation.

When the same fixed amount of gas moves between two states, the comparison form is often quicker:

p1V1/T1 = p2V2/T2.

Check whether the gas can reasonably be treated as ideal. In introductory problems, this assumption is normally intended when the ideal gas equation is provided or when the gas is sufficiently dilute and away from condensation conditions.

4. A gas expands or is compressed

For constant pressure, calculate work with W = pΔV. Expansion gives a positive ΔV and therefore positive work done by the gas. Compression gives a negative ΔV under this convention. More generally, work is represented by the area under a pressure–volume graph: W = ∫p dV. For a variable-pressure process, use the graph or the method specified by the question rather than automatically using pΔV.

To connect work with heating, use the first law. If 500 J of energy enters a system as heat and the system does 200 J of work, then ΔU = 500 − 200 = 300 J. The system’s internal energy increases because not all the supplied energy remains stored.

5. A heat engine or device has an efficiency

Thermal efficiency compares useful energy output with energy input:

η = Euseful/Einput = Wout/Qin.

To express efficiency as a percentage, calculate the ratio first and multiply by 100%. If a device receives 2,000 J and produces 500 J of useful work, its efficiency is 0.25, or 25%. For a heat engine, energy rejected to the surroundings means that useful work is less than the heat input in an ordinary operating cycle, so an efficiency above 100% signals an error in the setup or units.

What to double-check

Units: Convert grams to kilograms, litres to cubic metres, kilopascals to pascals, and Celsius to kelvin where an absolute temperature is required. A unit check can expose many factor-of-1,000 errors. For a broader method, see Dimensional Analysis in Physics.

Material data: Specific heat capacity and latent heat depend on the material and, in some contexts, on its state. Confirm whether the question gives a value or expects one from a formula sheet. Do not substitute the heat capacity of water for a metal simply because both are being heated.

Temperature versus temperature change: In Q = mcΔT, a difference in Celsius and a difference in kelvin have the same numerical size. In pV = nRT, however, T must be absolute temperature in kelvin.

Graph meaning: On a pressure–volume graph, the area under the curve represents work. On a heating curve, a flat section indicates energy transfer during a change of state rather than a temperature increase. For graph skills, use this guide to gradients, areas, and motion data.

Sign convention: Write down whether Q is positive for energy entering the system and whether W means work done by or on the system. Keep that choice unchanged throughout the calculation.

Common mistakes

  • Confusing heat with temperature: A large object can contain or transfer more energy than a small object at the same temperature. Temperature is not a measure of total thermal energy.
  • Using the wrong equation for a phase change: A material can absorb energy without rising in temperature while its state changes. Use mL for that interval.
  • Using Celsius in a gas law: Absolute temperature is required because gas-law relationships depend on temperature measured from absolute zero.
  • Mixing pressure and volume units: The combination Pa × m3 gives joules. If pressure is in kPa and volume is in litres, convert before using W = pΔV unless the question explicitly provides a compatible shortcut.
  • Dropping the mass factor: Specific heat capacity and specific latent heat are energy values per kilogram. Multiply by the total mass.
  • Rounding too early: Keep extra digits during intermediate steps and round the final result to an appropriate number of significant figures. The guide to uncertainty and significant figures can help with presentation.
  • Ignoring the process: The same gas can have different energy and work outcomes during constant-pressure, constant-volume, or changing-pressure processes. Identify the path, not just the initial and final values.

When to revisit

Return to this formula sheet before a thermal physics test, when a homework question introduces unfamiliar wording, or whenever you repeatedly confuse heat, temperature, and internal energy. A useful revision routine is to cover the equation column, classify each scenario from memory, and then uncover the formula to check your choice. Follow this with one calculation for each category: temperature change, latent heat, gas laws, work, internal energy, and efficiency.

Recheck the sheet at the start of each academic year and whenever your exam board, course specification, or permitted formula sheet changes. Pay particular attention to notation, required constants, unit conventions, and the sign convention for work. If you move from school physics to university thermodynamics, revisit the assumptions behind ideal gases and constant-pressure work rather than treating every formula as universal.

For a final exam or homework check, use this short workflow:

  1. Underline the process described in the question.
  2. List known quantities with units and identify the unknown.
  3. Choose the equation that matches the process.
  4. Convert units before substituting.
  5. Show rearrangement and substitution clearly.
  6. Check the unit, sign, scale, and physical meaning of the result.

Practising this classification step is more valuable than memorising a long list of equations without context. Once the process is clear, the formula is usually much easier to select and use.

Related Topics

#thermal-physics#heat-capacity#gas-laws#latent-heat#internal-energy#thermal-efficiency
S

StudyPhysics Editorial Team

Physics Education Editors

Senior editor and content strategist. Writing about technology, design, and the future of digital media. Follow along for deep dives into the industry's moving parts.