Electric circuits become easier to analyse when you identify the circuit’s nodes, branches, and loops before choosing an equation. This guide explains series and parallel circuits, Ohm’s law, Kirchhoff’s laws, equivalent resistance, power, internal resistance, and a practical troubleshooting workflow you can use for homework, laboratory work, and physics exam prep.
Overview
A circuit is a complete path through which charge can move. In a simple direct-current circuit, a source such as a cell provides a potential difference, or voltage, and components such as resistors transfer electrical energy. The current is the rate of charge flow, measured in amperes (A); voltage is energy transferred per unit charge, measured in volts (V); and resistance describes how strongly a component opposes current, measured in ohms (Ω).
The most useful starting equation is Ohm’s law:
V = IR
Here, V is the potential difference across a component, I is the current through it, and R is its resistance. Ohm’s law applies directly to ohmic components under conditions where their resistance remains approximately constant. Components such as filament lamps, diodes, and thermistors may not have constant resistance, so use the relationship between voltage and current shown by the component’s graph or specification.
Before calculating anything, translate the circuit diagram into a physical map:
- Mark the source and its polarity. Conventional current leaves the positive terminal and returns to the negative terminal through the external circuit.
- Mark every junction. A junction is a point where three or more conducting paths meet.
- Identify branches. A branch is a path between junctions. Components on separate branches may carry different currents.
- Identify loops. A loop is a closed path. Kirchhoff’s loop rule applies around any complete loop.
- Label unknown currents and voltages. Choose directions consistently. A negative calculated value means the real direction is opposite to your assumed direction.
This labelling step prevents a common mistake: treating a circuit that merely looks visually similar to a series or parallel circuit as though it follows the wrong rule.
What to track
Series and parallel circuits
Use the following comparison when deciding which rule applies:
| Feature | Series circuit | Parallel circuit |
|---|---|---|
| Path structure | One continuous path | Two or more branches between the same junctions |
| Current | The same current passes through each component | Current divides between branches |
| Voltage | The source voltage is shared between components | The same voltage appears across each branch |
| Equivalent resistance | Req = R1 + R2 + ... | 1/Req = 1/R1 + 1/R2 + ... |
For two resistors in parallel, the equivalent resistance can also be calculated as:
Req = (R1R2)/(R1 + R2)
The equivalent resistance of parallel resistors is always less than the smallest individual resistance. If your result is larger than the smallest branch resistance, check the calculation or the circuit classification.
Kirchhoff’s laws
Kirchhoff’s junction rule expresses conservation of charge:
Sum of currents entering a junction = sum of currents leaving a junction.
For example, if a current of 2.0 A reaches a junction and splits into currents of 0.8 A and I, then:
2.0 = 0.8 + I
so I = 1.2 A.
Kirchhoff’s loop rule expresses conservation of energy:
Sum of potential rises and potential drops around a complete loop = 0.
When travelling through a resistor in the direction of current, record a voltage drop of IR. Travelling through the resistor against the current gives a rise of IR. Crossing a source from its negative to positive terminal gives a positive rise of ε, where ε is the source’s electromotive force.
Power and energy transfer
Electrical power is the rate at which energy is transferred:
P = VI
Using Ohm’s law, you can also write:
P = I2R or P = V2/R
Choose the form that uses the quantities given in the question. Electrical energy transferred over a time interval is:
E = Pt
Check units carefully: power is measured in watts, energy in joules, and time must be in seconds when using SI units.
Internal resistance
A real cell has internal resistance, usually represented by r. Some of the source’s energy is transferred inside the cell rather than to the external circuit. The terminal potential difference is commonly modelled by:
V = ε - Ir
where ε is the emf and I is the circuit current. The internal resistance causes the terminal voltage to fall when the current increases. If a question includes both an external resistance R and internal resistance r, the current can often be found from:
I = ε/(R + r)
Cadence and checkpoints
Use a repeatable workflow whenever you meet an unfamiliar circuit. The order matters because it separates circuit interpretation from calculation.
- Redraw the circuit neatly. Use standard symbols and place the source, junctions, branches, and component values where they are easy to read.
- Choose current directions. In a simple series circuit there is one current. In a branched circuit assign a current to each independent branch or loop.
- Record known quantities with units. Convert prefixes such as kilo-, milli-, and micro- before substituting into equations.
- Simplify obvious series or parallel groups. Replace them with an equivalent resistance where possible, but do not simplify across a junction incorrectly.
- Apply Ohm’s law locally. Use the voltage across and current through the same component or equivalent section.
- Apply the junction rule. Write one current equation for each relevant junction.
- Apply the loop rule. Write enough independent loop equations to solve the remaining unknowns.
- Check the result. Test units, signs, limiting behaviour, and conservation of current and energy.
Worked example: A 12 V ideal supply is connected to a 4 Ω resistor in series with a parallel combination of 6 Ω and 3 Ω resistors. First combine the parallel pair:
1/Rp = 1/6 + 1/3 = 1/2, so Rp = 2 Ω.
The total resistance is therefore Rtotal = 4 + 2 = 6 Ω. The supply current is:
Itotal = 12/6 = 2 A.
The voltage across the 4 Ω series resistor is V = IR = 2 × 4 = 8 V. The parallel section receives the remaining 12 - 8 = 4 V. Each parallel branch has 4 V across it, so the 6 Ω branch carries 4/6 = 0.67 A and the 3 Ω branch carries 4/3 = 1.33 A. Their sum is 2.00 A, matching the current entering the parallel section.
This final current check is not optional decoration. It is a quick way to detect a misplaced decimal, an incorrect equivalent resistance, or confusion between branch current and total current.
How to interpret changes
When a circuit result changes, ask which physical variable changed and which conservation rule must still hold. Increasing a series resistance increases total resistance and usually reduces the total current for a fixed ideal voltage source. Adding another parallel branch decreases equivalent resistance, so the total current drawn from the source generally increases. However, the voltage across ideal parallel branches remains the same.
For a real source, increased current can produce a greater internal voltage drop, so the terminal voltage may decrease rather than remain perfectly constant. This distinction explains why a measured circuit may not match an ideal-source calculation exactly.
Use these diagnostic checks:
- If series components have different currents in your calculation, revisit the circuit map.
- If parallel branches have different voltages despite sharing both junctions, check the labels or measurement points.
- If current appears to enter a junction without leaving, apply Kirchhoff’s junction rule again.
- If a resistor’s calculated power is unexpectedly high, check whether you used VI, I2R, or V2/R with matching quantities.
- If an ammeter reading changes the circuit dramatically, check that it is connected in series. An ideal ammeter has very low resistance.
- If a voltmeter produces an unexpected reading, check that it is connected in parallel across the component being measured. An ideal voltmeter has very high resistance.
Also distinguish an open circuit from a short circuit. An open circuit has a broken path and ideally no current through the break. A short circuit provides a very low-resistance path, which can produce a large current and may bypass a component. In practical work, switch off the supply before changing connections and use the equipment limits provided by your teacher or laboratory instructions.
When to revisit
Return to this guide whenever you begin a new circuit topic, encounter a mixed series-parallel diagram, or make repeated errors with current and voltage labels. A useful revision checkpoint is to redraw one unfamiliar circuit from memory, classify every component relationship, and solve it without looking at the worked example. Then compare your answer using the junction, loop, unit, and limiting-value checks.
Before a test, practise one question of each type: a simple series circuit, a parallel circuit, a mixed network, a Kirchhoff loop problem, a power calculation, and a circuit with internal resistance. After laboratory work, revisit the article if measured values differ from predictions. Record the supply voltage, component values, current readings, and likely sources of uncertainty rather than changing equations merely to force agreement.
Refresh your personal circuit formula sheet when your course introduces a new convention or component model. The core rules remain stable, but diagrams, sign conventions, and the level of detail expected can vary between courses. For broader revision, connect circuit analysis with current, voltage, and resistance fundamentals, and use the site’s physics formula sheet to check symbols and units. The practical habit to keep is simple: map the circuit first, choose the rule second, calculate third, and test the result last.